Quantcast
Channel: Motor drivers forum - Recent Threads
Browsing all 15566 articles
Browse latest View live

Intefacing EK-TM4C123GXL with DRV8305 Evaluation Board

We are facing some issues while interfacing DRV8305 with EK-TM4C123GXL board.​We have interfaced this with SPI on ​EK-TM4C123GXL board with single PWM operation mode of DRV8305. but we are not getting...

View Article


Image may be NSFW.
Clik here to view.

DRV8711EVM SW Bug

Hello TI,I have been evaluating the DRV8711 for a while using the DRV8711EVM and Eval PCB. I've also designed it into my application, and FW is already being developed.I've noticed a really annoying...

View Article


Image may be NSFW.
Clik here to view.

DRV8842 Resoldered 100Hz output

Hello Team!I made a wrong connection to the DRV8842 IC and blew it up, so I wanted to replace it manually. I Dissoldered the broken chip with a hot air soldering tool, which was complicated because of...

View Article

[DRV8312] Switching problem with high current pulse

Dear TI's experts,I'm using DRV8312 to do sensorless BLDC algorithm without TI's library. I met a problem with the switching schematic:When a phase is in Hi-Z stage, at the first times working, its...

View Article

DRV8850 VPROPI pin voltage..

Hi,We are using DRV6650 in our design for motor drive. As per equation VPROPI resister set as 3K for 2.5 A current. we can get voltage as per theory :I*R/2000, but we cannot get voltage. we get only...

View Article


DRV8840 I0~I4 pin voltage level

HiMy customer is using DRV8840. He has a question about I0~I4 pin voltage level.Please see the attached file. Customer noticed abnormal voltage level of I0 and I4 pin.I0 pin is pulled up 5V through...

View Article

General getting-started BLDC driving/control questions

Folks,I'm interested in developing a motor controller/driver for a range of small BLDC motors (5-12v, <1amp) generally with a gear train (100-250x), to be used in small mobile robotic devices for...

View Article

Need +/- 2.5% speed regulation with DRV10983 on a fractional motor liquid pump.

Hi,I need +/- 2.5% speed regulation with  DRV10983 on a fractional motor liquid pump. We are pumping a liquid with variable viscosity and we need to estimate the pumped liquid volume using the motor...

View Article


Image may be NSFW.
Clik here to view.

DRV8835: Overcurrent Period Specification

Hi TI,The DRV8835 Data Sheet (see segment of page 5 below) defines an Output Overcurrent Deglitch period (Tdeg) of 1us, but is silent on the actual Overcurrent Period (e.g. 100us) prior to the MOSFET...

View Article


DRV8835: Output Configuration with four independent Resistive Loads

Hi TI,I'm planning to use the DVR8835 to drive an output configuration consisting of four independent resistive loads, each connected from a single Output pin to the common Ground reference (GND)....

View Article

DRV8412

In datasheet of DR8412 Application diagram. Recommended decoupling capacitor for GVDD 300uF. Can we reduce a value of it without reducing performance of the driver?

View Article

BLDC Motor with current regulation

Hello,Our customer looks for BLDC motor driver IC.His application is below.1) Take up a tape from reel with constant speed2) When it finished, strain a tape with constant currentDo you have any driver...

View Article

DRV8870 Tharmal resistance

HelloI have a question about thermal resistance of DRV8870DDA.Please tell me board information of 6.4 thermal infomation in datasheet.We would like to use it under the following conditions.- Ta=60℃-...

View Article


DRV8412 lowest frequency possible and corresponding bootstrap cap size?

We are using DRV8412 up to 10kHz.  Some applications are less than 100 Hz.  At 100 Hz what should the bootstrap cap be?  Is there a design equation?  The 5 ohm resistor on GVDD is already know, but for...

View Article

DRV8308 - recommended and safe values for charge pump capacitors

Hello!Assuming that 0.1uF/35V is a recommended capacitor for pins CP1 and CP2 (CP flying capacitor) on DRV8308, what would be the maximum tolerable capacitance? Or in other words, would the IC remain...

View Article


DRV8305 minimum pin configuration

Hello -I am building custom hardware, and have a question regarding the DRV8305. On the BOOSTXL-DRV8305, the "PWRGD" and "WAKE" pins are broken out. On the TIDA-00643 reference design, I see that the...

View Article

Image may be NSFW.
Clik here to view.

DRV8302 GVDD, AVDD, PVDD all output zero voltage

I am building a brushless motor controller for a motor rated at  60V and 80A using DRV8302 to drive the MOSFETs. We are are having some issues with the PVDD, GVDD and AVDD outputs on the DRV8302. We...

View Article


DRV8844 with sense resistor?

I'm looking for a replacement for the good old L298. DRV8844 seems what I'm looking for, but I'm not sure if I can add sense resistors for external current regulation to the device? The functional...

View Article

DRV8701 current chopping

Hello,I recently developed a brushed DC servo drive using the DRV8701 IC, and I was wondering if it is a good idea to feed the VREF pin with a low pass filtered PWM signal from my microntroller, to be...

View Article

DRV8305 Damage

Hi everyone..I'm using TMS320F28035 with DRV8305 motor driver. My custom board two layers. Top layer control unit. Bottom layer power unit and there are 6 mosfets (SUM110N06-3M9H-E3). I'm using...

View Article
Browsing all 15566 articles
Browse latest View live


Latest Images

<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>